- 1.00kg 이상 ~ 2.00kg 미만2,700원
- 2.00kg 이상 ~ 80.00kg 미만3,000원
제품소개: PC를 통해 아두이노를 프로그래밍하거나, PC와 아두이노간의 시리얼 통신 용도로 사용됩니다. 참고로 UNO는 본 변환기가 불필요합니다.
본 제품은 3.3V전원을 사용하는 아두이노 Pro, Pro Mini, FIO제품을 위한 USB to Serial변환기이며 별도의 커넥터 없이 위의 제품들과 직결됩니다.
본 변환기는 6핀헤더를 기본 장착하여 TX, RX, POWER(5V), GND, DTR, CTS 출력이 제공되며 DTR핀에 의해 프로그래밍시 오토리셋이 지원되어 프로그래밍시마다 리셋 스위치를 누르는 불편함이 없습니다.
내장된 TX LED, RX LED를 통해 시리얼 통신상태를 손쉽게 파악할 수 있습니다.
참고사항: DEV-09893과 포장만 다르고 기능은 동일
Description: This is the newest revision of our FTDI Basic. We now use a SMD 6-pin header on the bottom, which makes it smaller and more compact. Functionality has remained the same.
This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded. This is a really nice feature to have and allows a sketch to be downloaded without having to hit the reset button. This board will auto reset any Arduino board that has the reset pin brought out to a 6-pin connector.
The pins labeled BLK and GRN correspond to the colored wires on the FTDI cable. The black wire on the FTDI cable is GND, green is DTR. Use these BLK and GRN pins to align the FTDI basic board with your Arduino target.
There are pros and cons to the FTDI Cable vs the FTDI Basic. This board has TX and RX LEDs that allow you to actually see serial traffic on the LEDs to verify if the board is working, but this board requires a Mini-B cable. The FTDI Cable is well protected against the elements, but is large and cannot be embedded into a project as easily. The FTDI Basic uses DTR to cause a hardware reset where the FTDI cable uses the RTS signal.
This board was designed to decrease the cost of Arduino development and increase ease of use (the auto-reset feature rocks!). Our Arduino Pro and LilyPad boards use this type of connector.
Note: We know a lot of you prefer microUSB over miniUSB. Never fear, we’ve got you covered! Check out our FT231X Breakout for your micro FTDI needs!
Documents:
- 품절이나 주문상품 아이콘이 없는 제품은 하나 이상의 재고를 보유하고 있습니다.
- 산간벽지나 도서지방의 경우 별도의 추가금액을 지불하지 않으셔도 됩니다. 전국동일 (제주도 포함)
- 결제( 입금완료 )완료 후 1~2일 이내에 주문하신 제품을 받아 보실 수 있습니다. ( 우체국택배 ) 단, 품절 또는 주문상품( 해외수입 )의 경우 1~2주 정도 소요됩니다.
- 교환/반품의 경우 수령한 날로부터 7일까지 가능합니다. 단, 포장을 개봉하여 재판매가 불가할 경우 교환/반품이 불가합니다.
ITEM Q&A상품에 대해 궁금한 점을 해결해 드립니다.
글읽기 권한이 없습니다.
"19세 미만의 미성년자"는 출입을 금합니다!
no | subject | writer | data | hit |
---|---|---|---|---|
13 | 아두이노 피오 업로드 | 김애선 | 2015-04-19 | 155 |
12 | 아두이노 피오 업로드 | 아트로봇CT | 2015-04-19 | 155 |
11 | 라즈베리파이와 연결문의입니다. | 서종관 | 2014-10-20 | 2 |
10 | 라즈베리파이와 연결문의입니다. [2] | 아트로봇 | 2014-10-20 | 178 |
9 | 업로드 오류 | 이진수 | 2014-02-17 | 4 |