판매가 | |
---|---|
할인판매가 | 15,400원 (15,400원 할인) |
할인금액 |
총 할인금액 원 (모바일할인금액 원) |
적립금 |
100원(1.00%) 원% 원% 원% 원% 원% 원% 원% 원% 원% 원% 원% 원% 원% |
제휴적립금 | |
배송방법 | 택배 |
배송비 | 2,700원 ~ 3,000원 |
상품 추가설명 번역정보 |
배송 | |
---|---|
수량 |
상품 정보 | 가격 | 삭제 |
---|---|---|
총상품금액(수량)0 |
Description: This is the SparkFun ESP8266 Thing Dev Board – a development board that has been solely design around the ESP8266, with an integrated FTDI USB-to-Serial chip. The ESP8266 is a cost-effective, and very capable WiFi-enabled microcontroller. Like any microcontroller, it can be programmed to blink LEDs, trigger relays, monitor sensors, or automate coffee makers, and with an integrated WiFi controller, the ESP8266 is a one-stop shop for almost any Internet-connected project. To top it all off, the ESP8266 is incredibly easy-to-use: firmware can be developed in Arduino, and uploaded over a simple, serial interface. The ESP8266 Thing Development Board breaks out all of the module’s pins, and the USB-to-serial converter means you don’t need any peripheral components to program the chip. Just plug in a USB cable, download the Arduino board definitions, and start IoT-ing.
Why the name? We lovingly call it the “Thing” due to it being the perfect foundation for your Internet of Things project. The Thing does everything from turning on an LED to posting data with phant.io, and can be programmed just like any microcontroller. You can even program the Thing through the Arduino IDE by installing the ESP8266 Arduino addon.
The ESP8266 Thing Development Board is a relatively simple board. The pins are broken out to two parallel, breadboard-compatible rows. The USB connector sits next to an optional power supply input, and an ON/OFF switch – controlling power to the ESP8266 – sits next to that. And LEDs towards the inside of the board indicate power, charge, and status of the IC. The ESP8266’s maximum voltage is 3.6V, so the Thing has an onboard 3.3V regulator to deliver a safe, consistent voltage to the IC. That means the ESP8266’s I/O pins also run at 3.3V, you’ll need to level shift any 5V signals running into the IC. If your project requires a power source other than USB, the Thing Dev Board includes footprints for a 2-pin JST, 2-pin 3.5mm screw terminal, or a simple 0.1"-pitch 2-pin header. Unlike the original ESP8266 Thing, the ESP8266 Thing Dev Board does not have a built-in LiPo charger.
The Thing Dev Board even includes a PCB trace antenna as a default WiFi antenna, it’s cost-effective and actually works really well! If you need to connect a more sensitive antenna, or need to route outside an enclosure, a U.FL connector is also available on the board. Some soldering will be required to get the U.FL connector functioning but instructions can be found in the Hookup Guide we have written for the dev board.
Note: We’ve provided a few Example Sketches to experiment on your SparkFun ESP8266 Thing Development Board. These sketches can be found in the Hookup Guide in the Documents section below!
Features:
Documents:
01. 결제(입금완료)완료 후 2-3일이내에 상품을 수령하실 수 있습니다. 02. 재고가 없거나 다시 재입고 될 경우(예약상품, 구두포함) 5-7일이 소요됩니다. 03. 배송비는 5만원 이상 구매시 무료 5만원 미만 구매시 2500원의 배송료가 있습니다.
반품은 반드시 정해진 택배사를 이용해주세요. 반드시 고객센터나 게시판을 통해 반품의사를 알려주신 후 제품을 보내주셔야 합니다. 연락없이 보내실경우 반품 및 교환이 불가능합니다. 반품 및 교환에 대한 자세한 사항은 아래의 내용을 참고해주세요.
제품을 받으신 후 일주일 이내에 교환, 반품신청을 하지 않았을 경우 고객님의 부주의로 인한 상품이 변형, 훼손 또는 파손 된 경우 제품이 오염되었을 경우 (립스틱, 화장품, 음식물 기타 오염물질로 인해) 제품을 착용 및 사용하거나, 제품의 택(라벨)이 제거 했거나, 제품을 수선, 수리, 세탁하였을 경우 반품 불가로 표기 된 상품을 구매한 경우 (니트류, 화이트계열, 세일상품 등) 반품 의사를 통보하지 않고 반품한 경우