판매가 | |
---|---|
할인판매가 | 41,000원 (41,000원 할인) |
할인금액 |
총 할인금액 원 (모바일할인금액 원) |
적립금 |
400원(1.00%) 원% 원% 원% 원% 원% 원% 원% 원% 원% 원% 원% 원% 원% |
제휴적립금 | |
배송방법 | 택배 |
배송비 | 2,700원 ~ 3,000원 |
상품 추가설명 번역정보 |
배송 | |
---|---|
수량 |
상품 정보 | 가격 | 삭제 |
---|---|---|
총상품금액(수량)0 |
This lovely little shield is the best way to add a small, colorful and bright display to any project. We took our popular 1.8" TFT breakout board and remixed it into an Arduino shield complete with microSD card slot and a 5-way joystick navigation switch (with a nice plastic knob)! Since the display uses only 4 pins to communicate and has its own pixel-addressable frame buffer, it can be used easily to add a display & interface without exhausting the memory or pins.
The 1.8" display has 128x160 color pixels. Unlike the low cost "Nokia 6110" and similar LCD displays, which are CSTN type and thus have poor color and slow refresh, this display is a true TFT! The TFT driver (ST7735R) can display full 18-bit color (262,144 shades!).
The shield has the TFT display soldered on (it uses a delicate flex-circuit connector) as well as a ultra-low-dropout 3.3V regulator and a 3/5V level shifter so its safe to use with 5V Arduinos. We also had some space left over so we placed a microSD card holder (so you can easily load full color bitmaps from a FAT16/FAT32 formatted microSD card) and a 5-way navigation switch (left, right, up, down, select). The microSD card is not included, but you can pick one up here.
If you just want to display text, shapes, lines, pixels, etc the shield uses pins 13, 11, 10 and 8. If you'd like to add the navigation switch, it uses Analog 3 (all 5 switches are connected using a clever resistor trick to permit all the switches to share one analog pin). For the microSD card, you'll also give up Digital 12 and 4. This shield works best with the Arduino UNO and compatibles. You can use it with the Mega but it won't be as fast since it would be using software rather than hardware SPI for both the TFT and SD card, so it's not recommended.
Comes as a fully assembled and tested shield with the display, microsd card holder and nav switch with knob as well as a stick of 0.1" header. To finish up and use, you will need to solder on the header onto the shield PCB, a quick 10 minute task.
Of course, we wouldn't just leave you with a datasheet and a "good luck!" - we've written a full open source graphics library that can draw pixels, lines, rectangles, circles, text and bitmaps as well as example code and a wiring tutorial. The code is written for Arduino but can be easily ported to your favorite microcontroller!
Datasheets, Fritzing library, and EagleCAD PCB GitHub files available in the product tutorial
Specifications:
01. 결제(입금완료)완료 후 2-3일이내에 상품을 수령하실 수 있습니다. 02. 재고가 없거나 다시 재입고 될 경우(예약상품, 구두포함) 5-7일이 소요됩니다. 03. 배송비는 5만원 이상 구매시 무료 5만원 미만 구매시 2500원의 배송료가 있습니다.
반품은 반드시 정해진 택배사를 이용해주세요. 반드시 고객센터나 게시판을 통해 반품의사를 알려주신 후 제품을 보내주셔야 합니다. 연락없이 보내실경우 반품 및 교환이 불가능합니다. 반품 및 교환에 대한 자세한 사항은 아래의 내용을 참고해주세요.
제품을 받으신 후 일주일 이내에 교환, 반품신청을 하지 않았을 경우 고객님의 부주의로 인한 상품이 변형, 훼손 또는 파손 된 경우 제품이 오염되었을 경우 (립스틱, 화장품, 음식물 기타 오염물질로 인해) 제품을 착용 및 사용하거나, 제품의 택(라벨)이 제거 했거나, 제품을 수선, 수리, 세탁하였을 경우 반품 불가로 표기 된 상품을 구매한 경우 (니트류, 화이트계열, 세일상품 등) 반품 의사를 통보하지 않고 반품한 경우