판매가 | |
---|---|
할인판매가 | 10,900원 (10,900원 할인) |
할인금액 |
총 할인금액 원 (모바일할인금액 원) |
적립금 |
100원(1.00%) 원% 원% 원% 원% 원% 원% 원% 원% 원% 원% 원% 원% 원% |
제휴적립금 | |
배송방법 | 택배 |
배송비 | 2,700원 ~ 3,000원 |
상품 추가설명 번역정보 |
배송 | |
---|---|
수량 |
상품 정보 | 가격 | 삭제 |
---|---|---|
총상품금액(수량)0 |
감도 조절이 가능한 마이크로폰 내장된 프리앰프(사운드 센서)입니다. 입력된 소리를 증폭하여 출력해주며 이 신호를 활용하면 단순히 주변소리를 감지하능 용도나 뮤직 비주얼라이저를 제작할 수 있게 됩니다. 아두이노에서 입력된 소리를 변조하여 Wav쉴드등으로 출력하면 실시간 휴대용 음성변조기기 제작(동영상 및 관련 튜토리얼 참조)도 가능합니다.
알림. 뒷면에 장착된 트리머를 회전하여 원하는 감도(gain 이득)를 설정할 수 있습니다.
Add an ear to your project with this well-designed electret microphone amplifier. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use the Maxim MAX4466, an op-amp specifically designed for this delicate task! The amplifier has excellent power supply noise rejection, so this amplifier sounds really good and isn't nearly as noisy or scratchy as other mic amp breakouts we've tried!
This breakout is best used for projects such as voice changers, audio recording/sampling, and audio-reactive projects that use FFT. On the back, we include a small trimmer pot to adjust the gain. You can set the gain from 25x to 125x. That's down to be about 200mVpp (for normal speaking volume about 6" away) which is good for attaching to something that expects 'line level' input without clipping, or up to about 1Vpp, ideal for reading from a microcontroller ADC. The output is rail-to-rail so if the sounds gets loud, the output can go up to 5Vpp!
Using it is simple: connect GND to ground, VCC to 2.4-5VDC. For the best performance, use the "quietest" supply available (on an Arduino, this would be the 3.3V supply). The audio waveform will come out of the OUT pin. The output will have a DC bias of VCC/2 so when its perfectly quiet, the voltage will be a steady VCC/2 volts (it is DC coupled). If the audio equipment you're using requires AC coupled audio, place a 100uF capacitor between the output pin and the input of your device. If you're connecting to an audio amplifier that has differential inputs or includes decoupling capacitors, the 100uF cap is not required.
The output pin is not designed to drive speakers or anything but the smallest in-ear headphones - you'll need an audio amplifier (such as our 3.7W stereo amp) if you want to connect the amp directly to speakers. If you're connecting to a microcontroller pin, you don't need an amplifier or decoupling capacitor - connect the OUT pin directly to the microcontroller ADC pin.
For audio-reactive projects, we suggest using an FFT driver library (such as the one in this library) which can take the audio input and 'translate' it into frequencies. Also, check out this awesome Voice Changer project that uses this mic and an Adafruit Wave Shield!
01. 결제(입금완료)완료 후 2-3일이내에 상품을 수령하실 수 있습니다. 02. 재고가 없거나 다시 재입고 될 경우(예약상품, 구두포함) 5-7일이 소요됩니다. 03. 배송비는 5만원 이상 구매시 무료 5만원 미만 구매시 2500원의 배송료가 있습니다.
반품은 반드시 정해진 택배사를 이용해주세요. 반드시 고객센터나 게시판을 통해 반품의사를 알려주신 후 제품을 보내주셔야 합니다. 연락없이 보내실경우 반품 및 교환이 불가능합니다. 반품 및 교환에 대한 자세한 사항은 아래의 내용을 참고해주세요.
제품을 받으신 후 일주일 이내에 교환, 반품신청을 하지 않았을 경우 고객님의 부주의로 인한 상품이 변형, 훼손 또는 파손 된 경우 제품이 오염되었을 경우 (립스틱, 화장품, 음식물 기타 오염물질로 인해) 제품을 착용 및 사용하거나, 제품의 택(라벨)이 제거 했거나, 제품을 수선, 수리, 세탁하였을 경우 반품 불가로 표기 된 상품을 구매한 경우 (니트류, 화이트계열, 세일상품 등) 반품 의사를 통보하지 않고 반품한 경우