안녕하세요
시리얼통신 오류로 보입니다.
해당 오류발생 원인은 여러가지가 있습니다.
. 간혹 PC나 노트북의 USB 포트 오류 > 포트를 바꿔보시거나 PC를 변경해봅니다.
. USB 케이블 불량 : 다른 케이블로 교체
. 아두이노 스케치 프로그램 오류: 간혹 최신 버전의 SW가 시리얼통신 오류나
컴파일 오류가 나는경우가 종종있습니다.
> 아두이노 스케치 1.5x 가 아닌 1.x 버전으로 (한 버전 이전 안정버전으로)설치해보시기 바랍니다.
. 아두이노 드라이버 설치 오류 > 자동드라이버 설치가 불가하므로, 드라이버 파일 지정하여 재설치
. 윈도우 시스템의 일시적인 포트 오류 > 리부팅 후 해결
. D0, D1핀에 다른 부품이 연결된 경우 > 해당 부품 제거
. 아두이노 보드 의 MCU 나 시리얼통신칩 파손
(사용중 발생한 파손의 경우 따로 AS가 되지 않는점 양해부탁드립니다.)
---------- Original Message ----------
아두이노 최신 소프트웨어로 설치하고 장치관리자 통해서 COM 번호 맞췄고 툴을 아두이노 우노로 다 설정해놨는데도 업로드가 안됩니다.
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x6e
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x6e
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x6e
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x6e
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x6e
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x6e
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x6e
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x6e
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x6e
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x6e
다음과 같은 오류가 뜹니다
회원에게만 댓글 작성 권한이 있습니다.